Subscribe to Blog via Email
Join 6 other subscribersRecent Comments
- Patrick on Finished Paint and Final Assembly
- Neil Traver on Dash, Gauges and More
- Neil Traver on Clutch and Throttle Cable and Engine Wiring
- Neil Traver on Clutch and Throttle Cable and Engine Wiring
- Neil Traver on More Progress on Engine and Next Steps
Links
Categories
- Accelerator Pedal
- Accessory plug
- Air cleaner
- Alignment
- Aluminum Panels
- Battery
- Battery Box
- Battery disconnect
- Body Paint
- Brake Pedal
- Brake reservoir
- Build School
- bulb seal
- Cable
- Carpet
- Clutch Pedal
- Cockpit
- Dash
- Diode
- door
- Drive Shaft
- E-brake boot
- EFI
- Engine
- filler
- Flaring Tool
- Footbox
- Front brakes
- Front end
- Front suspension
- Fuel Filter
- Fuel Pump
- fuel pump pick-up
- Fuel System
- Fuel tank
- Gauges
- Ground strap
- Headers
- Heater vents
- heater-defroster
- hood
- Ignition
- Indicator lights
- Insulation
- J pipes
- Kit Info
- level probe
- Master Cylinder
- Mirrors
- O2 Sensor
- Oil relocation
- Panhard
- Parts
- Pedal Box
- Radiator
- Rage Gold
- Rear axle
- Rear Brakes
- Rear end
- Rear Suspension
- remote battery terminal
- Ride height
- Roll Bars
- sanding
- scoop
- seam
- Seat Belts
- Seat heaters
- seat tracks
- Seats
- Shifter boot
- Shop set-up
- Side Exhaust
- Sliders
- Speakers
- Starter
- Starter index plate
- Steering rack
- Steering Wheel
- Stereo
- Stripes
- Switches
- Transmission
- Trun signals
- Trunk
- Uncategorized
- Weatherpack
- weatherstrip
- welcome
- Wheels
- windshield
- wiper
- Wiper motor
- Wiring harness
Tags
Author Archives: dan
Fuel Lines
When the steering rack was completed, more we noticed that we could not tighten the tie rods enough on the threaded rod ends of the steering rack to get the front end close to being aligned. So, we had to … Continue reading
Steering Rack – Part 2
When the steering rack was completed, more we noticed that we could not tighten the tie rods enough on the threaded rod ends of the steering rack to get the front end close to being aligned. So, we had to … Continue reading
Sheet Metal Continued
The passenger compartment came next, Syphilis and for the most part went well. I ended up drilling some locations I did not need to – it became obvious after I had drilled and then moved on to the next pieces … Continue reading
Cockpit Sheet Metal
Next I started working on the cockpit sheet metal. The manual calls for marking, eczema doctor drilling and riveting into place. It was recommended to only mark and drill and use clecos to hold the metal in place. That way … Continue reading
Fuel Tank Installation
On September 7, condom Pat and I went to Freehold, women’s health New Jersey, buy more about to Proformance Unlimited, to observe the completion of the engine build. As a reminder, we decided to go with the Ford 302 small … Continue reading
Engine Update
On September 7, physician Pat and I went to Freehold, cost New Jersey, viagra to Proformance Unlimited, to observe the completion of the engine build. As a reminder, we decided to go with the Ford 302 small block, with the … Continue reading
Steering Rack
The steering rack in and of itself was a fairly straightforward process. The steps were relatively simple. Other issues did come up, diagnosis however, click which I will talk about later.  The work was to install a couple of … Continue reading
Pedal Box Build-up and Installation
Back at work on the rear brakes, ambulance I found that with a couple of washers included, there the calipers and rotors lined up very well. So, site that being completed, we went to work on the lower control arms … Continue reading
Heater – Defroster
While talking with some of my build school classmates, ailment they mentioned that they had actually painted the bare metal parts of the rear axle and brackets. This was recommended to them by another builder. So, I decided to do … Continue reading
Rear Axle Update
Back at work on the rear brakes, ambulance I found that with a couple of washers included, there the calipers and rotors lined up very well. So, site that being completed, we went to work on the lower control arms … Continue reading